Please return following links to the footer:
Designed by Frances Photography, thanks to: WordPress template, Home Birth Tips and WP free themes
CnAutotool-China Car diagnostic tool center

Category Chip Tuning Tools

Xprog 5.76 vs Xprog M 5.70 vs Xprog Box 5.60 vs Xprog-M 5.5

Xprog-M programmer is updated to Xprog box v5.76!! So, what’s new in Xprog box 5.76 programmer & what’s the differences among xprog box (xprog m) v5.76 v5.70 v5.60 v5.5.

What is Similarities of Xprog-M programmers v5.76 v5.70 v5.60 v5.5?

Xprog m programmer v5.76 v5.70 v5.60 v5.5 all share the authorization as below:

AUTH-0001 Motorola HC05 family authorization (allows to read/write EEPROM)

AUTH-0002 Motorola HC08 family authorization (allows to read/write EEPROM)

AUTH-0003 Motorola HC11 family authorization (allows to read/write EEPROM)

AUTH-0004 Motorola HC12, 9S12 family authorization (allows to read/write EEPROM and flash memory)

AUTH-0005 Texas Instruments TMS370/TMS374 family authorization (allows to read/write EEPROM)

AUTH-0006 Motorola HC05Bxx and HC05Xxx family bypass security ...

Read More

(Solution) KTAG master ECU programmer clone connected to Internet error

Here are two working solutions for you— when you connect KTAG K-TAG ECU Programming Tool to Internet unconsciously and K-TAG is locked. (Both two solutions are tested on forum, but still try on your own risk)

Problem 1:

I have met trouble with my Chinese clone KTAG master SW V2.13 FW V6.070. I connected the device to internet and now show C0000 in customer code and now 0 tokens. Anybody has a solution to this?

Solution:

You need new SD card of 4GB. Format new SD card fat 32, plug it in ksuite 2.08, with Update folder of 6.070, launch ksuite and start update. After finish all OK, with 30 tokens.

Problem 2:

My KTAG ECU programmer has been connected to Internet, now it’s locked! The client and group code just changed to C5555, I put new SD card in and it still not working...

Read More

How read Peugeot Boxer ECU Visteon DCU-102 with KTAG Master?

Here CnAutotool.com will show you how use KTAG Master to read Peugeot Boxer ECU Visteon DCU-102 (FOCOMO) in boot mode step by step!

ECU Type:

Visteon DCU-102 sometimes called FOMOCO.

Same unit and procedure applies to PSA, Ford and Fiat vans. In this case car is a Peugeot Boxer. No resistors required.

Tool you need:

KTAG ECU Programming Tool

K-TAG read ECU Visteon DCU-102 procedure:

Step1. Take out the ECU unit and heat the unit edges to open it safely.

Step2. Connect ECU with KTAG according to following pin out diagram:


Step3. Connect KTAG with computer then open ksuite software. Click the car icon and choose “Peugeot” and “Boxer III”. Then choose ECU: Visteon DCU102 KW 74 HP 11.

Step4. Click “Read” to start.

Wait the process complete to 100% and KTAG ECU Programme...

Read More

How to use KTAG Master to read VAG Audi A3 EDC17C46 ECU on bench?

Here is a tutorial for using KTAG Master ECU Programming Tool to read VAG Audi A3 ECU EDC17C46 on bench. Steps are as follows:

Step1. Open Audi A3 ECU EDC17C46 unit: first heat the edge to soften glue inside then open it carefully not to damage the circuit board.



Step2. Open K-TAG ECU Programmer software. Connect the cable 14P600KT02 to ECU connector according to following pin out diagram:



Step3. Take a wire, cut the wire cover at the middle. Solder its two ends to the two pins (red) as follow:




Click “Read” and wait it 100% complete. And then save the bin file.


Now KTAG Master read VAG Audi A3 ECU EDC17C46 successfully!

Read More