CAT Caterpillar ET<\/a><\/p>\n Installation Procedure<\/strong><\/p>\n WARNING! Be alert for sudden movement of the front link\u0002age and the work tool.<\/p>\n Do not insert fingers into the bores of the sup\u0002port pins when the support pins and the bores are being aligned.<\/p>\n NOTICE<\/strong> Removal Procedure<\/strong> Related Product\uff1a<\/strong><\/p>\n 2022 \u200bCAT SIS Service Information System<\/a><\/p>\n 1. Start the engine. Park the machine on a hard, level surface. Position the bucket, the stick, and the bucket control linkage, as shown. Shut off the engine.<\/p>\n 2. Slide O-ring seals (6) off the pin joints and onto the flanges of the bucket.<\/p>\n WARNING!<\/strong> Note: Removing the support pin may be difficult due to excessive pressure on the support pin. Remove the pressure on the support pin by adjusting the front linkag<\/p>\n 3. Remove bolt (7). Remove support pin (8). Caterpillar Hydraulic Information System (HIS)<\/strong><\/p>\n Installation Procedure 2. Position the O-ringseals(6) onto the flanges of the bucket Ill us tration 289g 03822736<\/p>\n 3.Start the engine and lower the stick into the bucket until the pin bores are in align ment with each other.Stoptheengine.<\/p>\n 4.Install support pin(9)into the pin bore.<\/p>\n 5.Install bolt(10)<\/p>\n 6.Referto Operation and Maintenance Manual,\u201cBucket Linkage-Inspect\/ Adjust\u201din order toad just the bucket clear ance.<\/p>\n 7.Slide O-ringseals(6)inposition over the pin joints between the bucket and the stick.<\/p>\n 8.Start theengineand position the bucket link age into the bucket until the pin boresare in align ment with each other.Stop the engine.<\/p>\n 9.Install support pin(8)into thep in bore.<\/p>\n 2019 Caterpillar Lift Trucks MCFE\/ MCFA\/ MCFS EPC+Service All in One VM Version<\/p>\n 10.Install Bolt(7).<\/p>\n 11.Slide theO-ringseals(6)over the pin joints between the bucket and the link assembly.<\/p>\n 12.Lubricate the bucket pins. Refer to Operationand Maintenance Manual,\u201cBucket Linkage-Lubricate\u201dor Operation and Maintenance Manual,\u201cBoom, Stick, and Bucket Linkage-Lubricate\u201d.<\/p>\n","protected":false},"excerpt":{"rendered":" Cat 325FLExcavator Bolted Flag RemovalProcedure and Caterpillar CAT Factory Password Calculator Generator 10 Digits VM Version Related Product\uff1a CAT Caterpillar ET Installation Procedure WARNING! Failure to follow the instruction below for the in\u0002stallation of a work tool may result in… Continue Reading
\nFailure to follow the instruction below for the in\u0002stallation of a work tool may result in personal in\u0002jury or death. Special care must be taken if more than one person is installing the work tool. Confirm the verbal communication and the hand signals that will be used during the installation.<\/p>\n
\nTo facilitate removal of the bucket pins without caus\u0002ing damage to the pins, the bearings, and\/or the O\u0002ring seals put the bucket on the floor and the stick in a vertical position, as shown.<\/p>\n
\n2022 Caterpillar SIS EPC+Service Manual download & Full Installation Service<\/p>\n![\"\"](\"https:\/\/www.cnautotool.com\/blog\/wp-content\/uploads\/2023\/01\/Caterpillar-Excavator-Bolted-Flag-Removal-Procedure-and-Installation-Procedure-1.png\")
<\/a><\/p>\n![\"\"](\"https:\/\/www.cnautotool.com\/blog\/wp-content\/uploads\/2023\/01\/Caterpillar-Excavator-Bolted-Flag-Removal-Procedure-and-Installation-Procedure-2.png\")
<\/a><\/p>\n
\nWhen the pin assembly is removed, the linkage assembly may swing out of the bucket. To pre\u0002vent possible personal injury, do not stand in front of the linkage assembly when the pin as\u0002sembly is being removed.<\/p>\n![\"\"](\"https:\/\/www.cnautotool.com\/blog\/wp-content\/uploads\/2023\/01\/Caterpillar-Excavator-Bolted-Flag-Removal-Procedure-and-Installation-Procedure-3.png\")
<\/a><\/p>\n
\n4. Remove bolt (10). Remove support pin (9).
\n5. Start the engine and raise the stick out of the bucket.
\n6. Remove the O-ring seals (6) from the flanges on the bucket
\nNote: After the support pins have been removed, make sure that the support pins do not become contaminated with sand or dirt. Make sure that the seals on the end of the stick and the seals on the end of the link do not become damaged.<\/p>\n
\n1. Clean each pin and each pin bore. Lubricate each pin bore with molybdenum grease.<\/p>\n![\"\"](\"https:\/\/www.cnautotool.com\/blog\/wp-content\/uploads\/2023\/01\/Caterpillar-Excavator-Bolted-Flag-Removal-Procedure-and-Installation-Procedure-4.png\")
<\/a><\/p>\n![\"\"](\"https:\/\/www.cnautotool.com\/blog\/wp-content\/uploads\/2023\/01\/Caterpillar-Excavator-Bolted-Flag-Removal-Procedure-and-Installation-Procedure-5.png\")
<\/a><\/p>\n