{"id":4642,"date":"2020-06-15T14:24:51","date_gmt":"2020-06-15T14:24:51","guid":{"rendered":"https:\/\/www.cnautotool.com\/blog\/?p=4642"},"modified":"2020-06-21T14:36:59","modified_gmt":"2020-06-21T14:36:59","slug":"yanhua-mini-acdp-program-key-for-jaguar-landrover-locked-kvm","status":"publish","type":"post","link":"https:\/\/www.cnautotool.com\/blog\/yanhua-mini-acdp-program-key-for-jaguar-landrover-locked-kvm\/","title":{"rendered":"Yanhua Mini ACDP Program Key for Jaguar LandRover Locked KVM"},"content":{"rendered":"

Yanhua Mini ACDP programming master<\/a> with KVM module 9 can support adding key and all keys lost for new Jaguar and Land Rover 2014-2018 no need soldering. Here share the related guide with ACDP users.<\/p>\n

Preparation:<\/strong><\/p>\n

ACDP host<\/p>\n

OBP+ICP adapter<\/p>\n

KVM interface board<\/p>\n

Copper pillar<\/p>\n

20 pin cable<\/p>\n

BAV-key<\/p>\n

Blank key<\/p>\n

KVM module (where is the position of KVM module in the car? See the procedure below)<\/p>\n

\"\"<\/a><\/p>\n

\"\"<\/a><\/p>\n

Procedure:<\/strong><\/p>\n

Step 1: Connect all the devices<\/p>\n

Open the trunk of the Jaguar\/ LANDROVER<\/p>\n

Find the location of KVM on the left and remove it<\/p>\n

\"\"<\/a><\/p>\n

Note: Land Rover\u2019s KVM module is generally located on the left side of trunk in the car<\/p>\n

\"\"<\/a><\/p>\n

\"\"<\/a><\/p>\n

Open the KVM module shell and remove the PCB<\/p>\n

\"\"<\/a><\/p>\n

Install KVM copper pillar<\/p>\n

\"\"<\/a><\/p>\n

D1-D4 regional figure<\/p>\n

\"\"<\/a><\/p>\n

Enlarged drawing<\/p>\n

\"\"<\/a><\/p>\n

Install the KVM interface board<\/p>\n

\"\"<\/a><\/p>\n

Aim for D1<\/p>\n

\"\"<\/a><\/p>\n

Aim for D2<\/p>\n

\"\"<\/a><\/p>\n

Aim for D3<\/p>\n

\"\"<\/a><\/p>\n

Aim for D4<\/p>\n

\"\"<\/a><\/p>\n

After D1-D4 is confirmed, press down the interface board<\/p>\n

Use PCB lock to fix one end of KVM interface board<\/p>\n

\"\"<\/a><\/p>\n

Install copper pillar to lock on the other end of the KVM interface board<\/p>\n

Connect ACDP host and ICP+OBP adapter<\/p>\n

\"\"<\/a><\/p>\n

Finally, power the ACDP host<\/p>\n

\"\"<\/a><\/p>\n

Step 2: Program key<\/p>\n

Open Mini ACDP APP<\/p>\n

Select \u201cJaguar\/ Land Rover\u201d-> \u201cJaguar\/LandRover add key\/all lost (2015-) -> \u201cIMMO\u201d<\/p>\n

\"\"<\/a><\/p>\n

\"\"<\/a><\/p>\n

 <\/p>\n

Loading resource\u2026<\/p>\n

Select \u201cKVM ICP (MC9S12XEQ384)\u201d-> \u201cAdd key auto mode\u201d<\/p>\n

\"\"<\/a><\/p>\n

\"\"<\/a><\/p>\n

Pay attention to the prompt<\/p>\n

\"\"<\/a><\/p>\n

\"\"<\/a><\/p>\n

Detecting pins status\u2026<\/p>\n

Pin detection passes<\/p>\n

\"\"<\/a><\/p>\n

KVM module chip has been encrypted, click \u201cContinue\u201d<\/p>\n

\"\"<\/a><\/p>\n

Reading chip PFLASH data\u2026<\/p>\n

Follow the prompt to save the original PFLASH data of the KVM module<\/p>\n

Confirm the PFLASH data save path<\/p>\n

\"\"<\/a><\/p>\n

Reading EEPROM\/DFLASH data\u2026<\/p>\n

Save the original EEPROM data of the KVM module<\/p>\n

Confirm EEPROM data save path<\/p>\n

\"\"<\/a><\/p>\n

Save the original PFLASH data of the KVM module<\/p>\n

Confirm DFLASH data save path again<\/p>\n

Check VIN and other vehicle information<\/p>\n

\"\"<\/a><\/p>\n

Follow the prompt to connect ACDP device to the BAV-key adapter<\/p>\n

\"\"<\/a><\/p>\n

Check the blank key ID<\/p>\n

\"\"<\/a><\/p>\n

Reading key information\u2026<\/p>\n

Select any blank key number<\/p>\n

\"\"<\/a><\/p>\n

Programming key\u2026<\/p>\n

Save the EEPROM data of the KVM module after adding the key<\/p>\n

Confirm the new EEPROM data save path<\/p>\n

\"\"<\/a><\/p>\n

Save the new DFLASH data of the KVM module after adding the key<\/p>\n

Confirm the new DFLASH data storage path<\/p>\n

\"\"<\/a><\/p>\n

Follow the prompt to connect ACDP device, OBP+ICP adapter, KVM interface board and KVM module to ensure normal communication<\/p>\n

\"\"<\/a><\/p>\n

Checking pin again\u2026<\/p>\n

Pin detection passes<\/p>\n

\"\"<\/a><\/p>\n

It will prompt \u201cKVM module chip has been encrypted\u201d again, just click \u201cContinue\u201d<\/p>\n

Check the new key ID is in the key list<\/p>\n

\"\"<\/a><\/p>\n

Writing EEPRM\/DFLASH data\u2026<\/p>\n

Yanhua Mini ACDP add the new key completed<\/p>\n

Install the KVM module to the car and confirm that the new key can be used normally<\/p>\n

\"\"<\/a><\/p>\n

Yanhua mini acdp do JLR locked kvm\u2019s Feedback\u00a0<\/strong><\/p>\n

Someone wonder if Yanhua mini acdp do JLR locked kvm\u2019s, some says 100% yes, someone says yes but need skills, someone says tried with no lucky. This article tell the truth and share the guide.<\/p>\n

Feedback 1: 100% yes<\/strong>
\nYanhua mini acdp does JLR locked kvm\u2019s. I did one today.<\/p>\n

Feedback 2: yes but need skills<\/strong>
\nIt\u2019s done everything I\u2019ve asked of it so far.
\nJLR locked kvm
\nFEM and bdc spare keys
\nCas3+ 9389115 all keys lost
\nMake sure you\u2019re using the correct frequency keys though. I had one wrongly labeled as 433 when it was 315 and that caused problems.
\nOnly discovered when I went to do it with CGDI and it spotted the wrong frequency. ACDP doesn\u2019t check obviously.<\/p>\n

Feedback 3: with no luck<\/strong>
\nThe constant warnings about poor wifi when its a full strength, it still can\u2019t crack encrypted KVM\u2019s.
\nIt struggles to even read them.<\/p>\n

The software constantly locks making you have to close the app and power down the interface to reset it.<\/p>\n","protected":false},"excerpt":{"rendered":"

Yanhua Mini ACDP programming master with KVM module 9 can support adding key and all keys lost for new Jaguar and Land Rover 2014-2018 no need soldering. Here share the related guide with ACDP users. Preparation: ACDP host OBP+ICP adapter… Continue Reading →<\/span><\/a><\/p>\n","protected":false},"author":1,"featured_media":4662,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":[],"categories":[14],"tags":[1015,685,1012,1013,1014,1011,1016,1010,1375],"_links":{"self":[{"href":"https:\/\/www.cnautotool.com\/blog\/wp-json\/wp\/v2\/posts\/4642"}],"collection":[{"href":"https:\/\/www.cnautotool.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.cnautotool.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.cnautotool.com\/blog\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.cnautotool.com\/blog\/wp-json\/wp\/v2\/comments?post=4642"}],"version-history":[{"count":2,"href":"https:\/\/www.cnautotool.com\/blog\/wp-json\/wp\/v2\/posts\/4642\/revisions"}],"predecessor-version":[{"id":4681,"href":"https:\/\/www.cnautotool.com\/blog\/wp-json\/wp\/v2\/posts\/4642\/revisions\/4681"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.cnautotool.com\/blog\/wp-json\/wp\/v2\/media\/4662"}],"wp:attachment":[{"href":"https:\/\/www.cnautotool.com\/blog\/wp-json\/wp\/v2\/media?parent=4642"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.cnautotool.com\/blog\/wp-json\/wp\/v2\/categories?post=4642"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.cnautotool.com\/blog\/wp-json\/wp\/v2\/tags?post=4642"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}