{"id":5549,"date":"2020-08-21T12:50:09","date_gmt":"2020-08-21T12:50:09","guid":{"rendered":"https:\/\/www.cnautotool.com\/blog\/?p=5549"},"modified":"2020-08-23T12:56:54","modified_gmt":"2020-08-23T12:56:54","slug":"porsche-cayenne-2011-epb-programming-after-replacement-by-launch-x431-2","status":"publish","type":"post","link":"https:\/\/www.cnautotool.com\/blog\/porsche-cayenne-2011-epb-programming-after-replacement-by-launch-x431-2\/","title":{"rendered":"Porsche Cayenne 2011 EPB Programming after Replacement by Launch X431"},"content":{"rendered":"

In this instruction,i will show you how to use Launch X431<\/a> to calibrate EPB for Porsche Cayenne 2011- after replacement. This function allows you to maintain the electronic parking brake system safely and efficiently. Main functions include: Put the handbrake pad to the installation position, check the basic setting of the parking brake (check the gap of the handbrake pad), handbrake pad run-in and calibration.<\/p>\n

\"\"<\/a><\/p>\n

For more repair case about Porsche,please refer to:Porsche Cayenne Repair Cases<\/a>.<\/p>\n

Cautions:<\/strong><\/p>\n

The replacement of Porsche Cayenne rear brake pads is the same as the replacement of ordinary brake pads. If you accidentally clicked on the menu of put handbrake pad to installation position, you must strictly follow the maintenance index to restore the electronic handbrake. After the replacement of handbrake pad, check the basic setting of the parking brake. Check the gap of the handbrake pad (standard gap is 1.9mm-2.4mm). Continue if this is OK. After the replacement of handbrake pad, the running-in function must be performed before the calibration.<\/p>\n

Porsche Cayenne EPB Calibration:<\/strong><\/p>\n

1.Select Porsche Version V21.51 or above.<\/p>\n

2.Select manual selection ->Cayenne(as of 2011) -> system selection ->parking brake ->special function<\/p>\n

\"\"<\/a><\/p>\n

3.Click maintenance index, read the index information.<\/p>\n

\"\"<\/a><\/p>\n

4.When replace the handbrake pad, select the function \u201cPut hand brake pad to installation position\u201d. After carrying out the function successfully as prompted, replace the brake pad. After the installation of new handbrake pad, select the function \u201cCheck basic setting of parking brake\u201d<\/p>\n

\"\"<\/a><\/p>\n

5.Click \u201cOK\u201d button, the actuator will complete a process of tension and release<\/p>\n

\"\"<\/a><\/p>\n

6.Click \u201cNext\u201d to check the gap of the handbrake pad, see Picture 5.Note, the standard gap of Cayenne (as of 2011) is 1.9mm-2.4mm. If out of this range, please adjust it manually.<\/p>\n

\"\"<\/a><\/p>\n

7.Click \u201cNext\u201d to complete the function \u201cCheck basic setting of parking brake\u201d<\/p>\n

\"\"<\/a><\/p>\n

8.After adjusting the gap, select \u201crunning-in\u201d to run in the steel handbrake pad<\/p>\n

\"\"<\/a><\/p>\n

9.After the replacement of handbrake pad, running-in must be performed! This function equals to adaptive learning. The instrument panel will prompt \u201cParking system enters maintenance mode\u201d. This function requires one person to drive and another person to operate the software. It also has strict requirement to the site. Please be well prepared. Calibration should be performed only after the completion of 8 times of successful running-in,<\/p>\n

\"\"<\/a><\/p>\n

10.Select \u201cCalibration\u201d<\/p>\n

\"\"<\/a><\/p>\n

11.After satisfying the calibration conditions, click OK to perform the \u201cCalibration\u201d of the parking brake. When it prompts the calibration is complete, the software operation of replacing the handbrake pad is complete<\/p>\n

\"\"<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"

In this instruction,i will show you how to use Launch X431 to calibrate EPB for Porsche Cayenne 2011- after replacement. This function allows you to maintain the electronic parking brake system safely and efficiently. Main functions include: Put the handbrake… Continue Reading →<\/span><\/a><\/p>\n","protected":false},"author":1,"featured_media":5560,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":[],"categories":[5,1381,240],"tags":[615,2462,234,1040,1039,1041,656],"_links":{"self":[{"href":"https:\/\/www.cnautotool.com\/blog\/wp-json\/wp\/v2\/posts\/5549"}],"collection":[{"href":"https:\/\/www.cnautotool.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.cnautotool.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.cnautotool.com\/blog\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.cnautotool.com\/blog\/wp-json\/wp\/v2\/comments?post=5549"}],"version-history":[{"count":2,"href":"https:\/\/www.cnautotool.com\/blog\/wp-json\/wp\/v2\/posts\/5549\/revisions"}],"predecessor-version":[{"id":5562,"href":"https:\/\/www.cnautotool.com\/blog\/wp-json\/wp\/v2\/posts\/5549\/revisions\/5562"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.cnautotool.com\/blog\/wp-json\/wp\/v2\/media\/5560"}],"wp:attachment":[{"href":"https:\/\/www.cnautotool.com\/blog\/wp-json\/wp\/v2\/media?parent=5549"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.cnautotool.com\/blog\/wp-json\/wp\/v2\/categories?post=5549"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.cnautotool.com\/blog\/wp-json\/wp\/v2\/tags?post=5549"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}